Well Crap.... LOL. The darn thing has gone for hours without graphing and now it started working....
Sorry! :D
ffuentes |
Well it did it again. It has not log data for about 1hr. while port number 1 is loging ok.
ffuentes |
lol.... And now it works again... :/
on3ptz |
Make sure there is no plastic from the wires under the connector ...
ffuentes |
There is not... something is not right it only logs for hours at a time. It has not log data sense 9AM this morning...
ffuentes |
I think I just figure out what is going on.
on3ptz |
are you sure the phase is in use for small equipment ?
i have also one phase that is only working when my oven or boiler is working.
ffuentes |
Yeap that is what is going on.
I have a clamp hooked up to my AC unit. The Breaker is 40AMPS and I put a 50AMP clamp.... It only logs when it activates of course but the issue I have is that after some time the graph just disappears instead of flat lining... Than there is a delay between graphs and one gets behind from the others.... It's some what odd...
ffuentes |
Now my monthly graph disappeared...
[IMG]http://i106.photobucket.com/albums/m260/xcom7/Networking/problems_flukso.jpg[/IMG]
icarus75 |
Flukso's internal plumbing is based on 'pulses'. For electricity metering one pulse = 1Wh of consumption. No consumption means no pulses, hence no graph since the last occurrence of a pulse.
ffuentes |
Icarus75,
No. Something is wrong with the flukso graphing system.
All of my data got erased on the monthly tab.
Please see the provided link.
This is not a pulse problem.
icarus75 |
I just took a look at your dash. All charts (hour/day/month/year/night) render just fine on my side. If the issue is still present for you, what browser type + version are you using?
ffuentes |
Icarus75,
It was all working until a few weeks a go.
Chromium Version 21.0.1180.90 (156592)
Firefox 16.0.2
Thank You.
icarus75 |
I've re-checked your charts with FF 16.0.2. Your time series are rendered correctly. So I'm a bit puzzled here.
Well Crap.... LOL. The darn thing has gone for hours without graphing and now it started working....
Sorry! :D
Well it did it again. It has not log data for about 1hr. while port number 1 is loging ok.
lol.... And now it works again... :/
Make sure there is no plastic from the wires under the connector ...
There is not... something is not right it only logs for hours at a time. It has not log data sense 9AM this morning...
I think I just figure out what is going on.
are you sure the phase is in use for small equipment ?
i have also one phase that is only working when my oven or boiler is working.
Yeap that is what is going on.
I have a clamp hooked up to my AC unit. The Breaker is 40AMPS and I put a 50AMP clamp.... It only logs when it activates of course but the issue I have is that after some time the graph just disappears instead of flat lining... Than there is a delay between graphs and one gets behind from the others.... It's some what odd...
Now my monthly graph disappeared...
[IMG]http://i106.photobucket.com/albums/m260/xcom7/Networking/problems_flukso.jpg[/IMG]
Flukso's internal plumbing is based on 'pulses'. For electricity metering one pulse = 1Wh of consumption. No consumption means no pulses, hence no graph since the last occurrence of a pulse.
Icarus75,
No. Something is wrong with the flukso graphing system.
All of my data got erased on the monthly tab.
Please see the provided link.
This is not a pulse problem.
I just took a look at your dash. All charts (hour/day/month/year/night) render just fine on my side. If the issue is still present for you, what browser type + version are you using?
Icarus75,
It was all working until a few weeks a go.
Chromium Version 21.0.1180.90 (156592)
Firefox 16.0.2
Thank You.
I've re-checked your charts with FF 16.0.2. Your time series are rendered correctly. So I'm a bit puzzled here.