Hi,

Just installed a water sensor,
Even after almost 24 hours I only get the lperday in the Minute graph,.... which then obviously only shows the curve for the last few minutes.

The sensor works because every time water is flowing it detects it in the lperday (minute) graph and it increases the lperday value.

Before I hooked up the sensor I tested it by placing it in a LED circuit, when I had the water flowing the led pulsed (went of and on), ... so this looks fine, the only odd thing is that when the water stops flowing it often happens that the sensor keeps the pulse high and this can last for a long time until the water is flowing again when it starts to blink again. Is this a known/normal behaviour ?

Also, I'm getting weird read ins in the /var/run/fluksod/sensor file,... when I have the water flowing it produces values but when it is not flowing I get:

Anyone some clues ?

root@flukso-2f2a7a:/tmp/run/fluksod/sensor# cat 5b798bfaa87c0867bec168b8a83c7be6
[[1387104544,"nan"],[1387104545,"nan"],[1387104546,"nan"],[1387104547,"nan"],[1387104548,"nan"],[1387104549,"nan"],[1387104550,"nan"],[1387104551,"nan"],[1387104552,"nan"],[1387104553,"nan"],[1387104554,"nan"],[1387104555,"nan"],[1387104556,"nan"],[1387104557,"nan"],[1387104558,"nan"],[1387104559,"nan"],[1387104560,"nan"],[1387104561,"nan"],[1387104562,"nan"],[1387104563,"nan"],[1387104564,"nan"],[1387104565,"nan"],[1387104566,"nan"],[1387104567,"nan"],[1387104568,"nan"],[1387104569,"nan"],[1387104570,"nan"],[1387104571,"nan"],[1387104572,"nan"],[1387104573,"nan"],[1387104574,"nan"],[1387104575,"nan"],[1387104576,"nan"],[1387104577,"nan"],[1387104578,"nan"],[1387104579,"nan"],[1387104580,"nan"],[1387104581,"nan"],[1387104582,"nan"],[1387104583,"nan"],[1387104584,"nan"],[1387104585,"nan"],[1387104586,"nan"],[1387104587,"nan"],[1387104588,"nan"],[1387104589,"nan"],[1387104590,"nan"],[1387104591,"nan"],[1387104592,"nan"],[1387104593,"nan"],[1387104594,"nan"],[1387104595,"nan"],[1387104596,"nan"],[1387104597,"nan"],[1387104598,"nan"],[1387104599,"nan"],[1387104600,"nan"],[1387104601,"nan"],[1387104602,"nan"],[1387104603,"nan"]]

Hi flukso community,

I joined you yesterday with my FLM in the mail and eagerly tried to set it up.
So it was not problem connecting it to the wireless network, and seeing the device and sensors beeing connected online. As access to the fusebox is a bit constarained in my case I tried to simulate the setup by putting the clamps around my laptops powercord. I was hoping to see at least some readings on the dashboard page. But now after 16 hours of uptime there is still only a blank screen.
So I started to play around with the sensor settings and disabled all of them: what is puzzling me that there are still two sensor active, which are the
electricity smart-main
gas smart-main
sensors.
Any idea whats going wrong or whether simulating the flukso as I did just doesn´t create any out put?
Thanks for any hint

Erik

On my first 24h that i have the FLM up and running, i see different readings in the dash when i compare day and hour. On the hour tab, when i pulled the left handle complete open to see 24h and i thought that it would be the same then the readings on the day tab. It is not the case, the piek consumpsion is lower then on the hour tab.
Why is that , this is like an lower resolution on day readings ? See also the 2 printscreens here:
Day: http://ubuntuone.com/3h3IdIgw4bTzUCbbUADLNo
Hour: http://ubuntuone.com/7aw4YfQtr66J7354dmbEo4

Hello,
After ordening a Flukso version v2b with a 50A clamp last week on 6 decmber, i was wondering when the goods chall arrive at my home here in Gent (be) ?
In my account on the Order status i see only Order created and Payment recieved.
The order number is 958...
Thanks :-)

Are there any applications yet for the RFM12B / Jeenode interface on the FLM v2b?

Looks like it could be useful if/when the interfaces and software are available.