Installation

Questions about installing and configuring a Fluksometer.

Dash/Minute graph access timeout

Hi,
Some times ago, I found in Flukso forum a way to open access to the Flukso box's web interface via Wifi.
I followed the procedure and now I am not obliged to connect physically an UTP cable on the box to modify some parameters in the web interface.

But now I cannot see the Dash/Minute graph any more.

The strange behavior is that I can still see the Dash/Minute graph on my iPad. On my Linux computer, whether I use Chrome or Firefox, I still get the message about a timeout occuring, or about the fact that I am not in the same LAN as the Flukso box.
My computer is connected on the same WIFI SSID as my iPad.

This behavior started exactly on the moment I have modified the firewall of the Flukso box.

Any help would be appreciated.

Thank!
LOUIS

Gone AWOL

Then, while accessing it via wired interface to check the log (which showed nothing special except it couldn't resolve network hosts), it suddenly connected again, shows up on the website under devices (heartbeat received) but no data being uploaded.

Any thoughts on how to figure out what's happening?

PVOutput upload double the power

I saw a lot of people are using PVoutput to upload sensor data. I was trying to do the same but face very strange problem.
Consumption shown on pvoutput is always double consumption shown on flukso graph.
Does anyone has hints on how to fix this ?
thanks a lot

Krijg geen data uit de FLM2

Hallo,

Ik heb 3 clamps 100,50 en 100A op separate kabels geklemd (1-fase) zonder de 'schil' te verwijderen.
Op dit moment ontvang ik de data als volgt (vb 1 sensor)
http://192.168.20.43:8080/sensor/80ef4aa13a52aae5279c36b41e96b4c2?versio...
levert
realtime([[1347701413,0],[1347701414,0],[1347701415,0],[1347701416,0],[1347701417,0],[1347701418,0],[1347701419,0],[1347701420,0],[1347701421,0],[1347701422,0],[1347701423,0],[1347701424,0],[1347701425,0],[1347701426,0],[1347701427,0],[1347701428,0],[1347701429,0],[1347701430,0],[1347701431,0],[1347701432,0],[1347701433,0],[1347701434,0],[1347701435,0],[1347701436,0],[1347701437,0],[1347701438,0],[1347701439,0],[1347701440,0],[1347701441,0],[1347701442,0],[1347701443,0],[1347701444,0],[1347701445,0],[1347701446,0],[1347701447,0],[1347701448,0],[1347701449,0],[1347701450,0],[1347701451,0],[1347701452,0],[1347701453,0],[1347701454,0],[1347701455,0],[1347701456,0],[1347701457,0],[1347701458,0],[1347701459,0],[1347701460,0],[1347701461,0],[1347701462,0],[1347701463,0],[1347701464,0],[1347701465,0],[1347701466,0],[1347701467,0],[1347701468,0],[1347701469,0],[1347701470,0],[1347701471,0],[1347701472,"nan"]]);

hoop nullen. tegelijkertijd ontvang ik op de flukso.net site foutmeldingen bij de minuut weergave van de data. er gaat daadwerkelijk wel stroom door de diverse kabels voorzien van clamps. Aangezien ik geen data gevisualiseerd krijg, mijn vraag; zit de basis goed aangesloten? Waar of wat moet ik wijzigen zodat er data gaat stromen/visueel wordt gemaakt?
mvg

Jan

Schlumberger G4 RF1

Hi,
did anyone manage to get the gas sensor working on a Schlumberger G4 RF1 meter? (see photos)
Thanks