Connected my brand new FLM v2b software 232 to my P1 port of a Kaifa smart meter (Dutch)

- Kaifa smart meter with P1, modelyear 2014, recently installed
- wiring connected to FLM ports 6a, 6b and 5-
- hooked up to router using cable, ping working correctly
- dash keeps telling me: "Error - The call for sensor smart-main experienced a timeout. You are probably not in the same local network as the FLM".
- dash data is blank

- I can connect to and log-in to the FLM, from the lan.
- device sends heartbeat to Devices list at Flukso.net
- Two sensors seem to be registered at the sensors list (smart-main, gas and electricity) at Flukso.net

Checked the forum, but I can't find an answer.

Can anybody tell me what's wrong or where to start looking?

Tx.

Last few syslog lines, hope it's useful:
Oct 10 20:56:24 flukso-deb535 cron.err crond[575]: time disparity of 23549575 minutes detected
Oct 10 21:00:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 806 cmd /usr/bin/fcheck
Oct 10 21:01:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 827 cmd /usr/bin/heartbeat 0
Oct 10 21:01:07 flukso-deb535 user.info heartbeat[828]: POST https://api.flukso.net/device/deb535612c275a97d1db4e610ccce906: 200
Oct 10 21:15:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 896 cmd /usr/bin/fcheck
Oct 10 21:30:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 1016 cmd /usr/bin/fcheck
Oct 10 21:45:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 1049 cmd /usr/bin/fcheck
Oct 10 22:00:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 1082 cmd /usr/bin/fcheck
Oct 10 22:01:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 1103 cmd /usr/bin/heartbeat 0
Oct 10 22:01:04 flukso-deb535 user.info heartbeat[1104]: POST https://api.flukso.net/device/deb535612c275a97d1db4e610ccce906: 200
Oct 10 22:15:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 1122 cmd /usr/bin/fcheck
Oct 10 22:30:01 flukso-deb535 cron.info crond[575]: crond: USER root pid 1205 cmd /usr/bin/fcheck

Hi there,

Do I need the wifi to connect to the internet to post the readings?
At my home, I'd would like to eliminate the use of wifi connections as much as possible.
Where do I change the network settings, like IP-address?
regards,
Bart

Hi,

I'm using a flukso V2b model, with ports 2, 3, 4 and 5 configured as pulse inputs.
However I need an "extra" pulse input. So instead of buying a new fluso for this, could it be possible to configure (perhaps through ssh) port 1 also as a "pulse" port instead of analog ?

thx

Hi,
I configured my flukso device but when i try to connect trow wifi to it, it doesnt give me a response.
I dont know what im doing wrong, anyone help?

Sinds april 2014 heb ik een nieuwe slimme meter: Kaifa MA304.
Daarvoor was de FLM02B aangesloten aan de P1 poort van Landis + Gyr.
Het inlezen en weergeven van de verbruiksdata werkte toen goed.
Sinds de FLM02B aangesloten is aan de Kaifa MA304 worden de data niet meer getoond. Nu heb ik gehoord dat de Kaifa MA304 werkt met het DSMR 4.0 protocol en de Landis + Gyr met het DSMR 2.2 protocol. Zou het kunnen zijn dat de FLM02B niet met het DSMR 4.0 protocol over weg kan ? Als dat zo is: wanneer wordt een upgrade daarvoor verwacht ?